REMOTE

GETTING STARTED

1.Placement

The best recommended projection size is 80 inches.

2.Power on

①Connect the projector to the power outlet.

4.Remote Control Pairing

NETWORK SETTINGS

• Go to [Settings], select [Network & Internet], and turn on Wi-Fi.
• Choose your network and enter the correct password.

FOCUS SETTINGS

Autofocus

Manual focus

IMAGE CORRECTION SETTINGS

• Go to [Projector] -- [Image Correction].
• Select [Auto Keystone Correction], and the screen will automatically be corrected
• Select [Manual Keystone Correction], and use navigation keys to adjust the four points and the image shape.

BLUETOOTH SPEAKER MODE

• Go to [Settings], select [Projector], and click on [Bluetooth Speaker Mode].
• Connect your phone to a device with the Bluetooth name containing"HAVIT PJ209APlus".
• When you hear "Bluetooth connection successful", the projector can play music from your phone.
• Press and hold the "Back" key on remote control for 2 seconds to[Bluetooth speaker mode].

GOOGLE ASSISTANT

1.Screen mirroring with Google Cast

2.Screen Mirroring via AirScreen

1. No audio output

• Check if the projector is muted. If so, press [Mute] key again to unmute the projector.
• Check if the projector interface "HDMI ARC" or Bluetooth is connected to an externa| audio device.

2. No image output

• Press [Power] button at the rear of the projector. The power indicator light will turn on if the projector enters projection mode successfully.
• Ensure that the power adaptor has specified power output.

3. No network

• Enter [Setting] via [Dash board], and check the internet connection status in the network option.
• Ensure that the network cable is correctly inserted to the projector interface "LAN".
• Ensure that the router is correctly configured.

4. Fuzzy Image

• Adjust the focus or keystone correction of the projector.
• Make sure the projection distance is in the effective focal range of the projector.
• Remove the dust or dirt from the lens with a blower or soft-bristled brush.

5. Non-rectangular Image

• Place the projector perpendicular to the screen/wall if keystone correction function is not used.
• Use the keystone correction function to adjust image shape.

6. Automatic keystone correction failure

• Make sure the TOF module on the front glass cover of the projector is not blocked or smudged.
• Move the projector until it is perpendicular to the projection surface and try again.

7. Autofocus failure

• Make sure the TOF on the front glass cover of the projector is not blocked or smudged.
• Move the projector back and forth until the projector is in recommended projection distance.

8. Remote control unresponsive

• Make sure the batteries are installed correctly and not drained.
• Remove any obstructions between your projector and remote control.
• Ensure the remote contro| is successfully paired with projector via Bluetooth.
• Make sure no button is pressed or stuck and check if the power indicator is still on. If yes, please contact customer support or local service center.

9. Connect the Bluetooth devices

• Enter [Settings], open the [Bluetooth] option to check the Bluetooth device list, and connect the device.

10. Cannot power on the projector

• The projector will enter protection mode if the interna| battery runs out. In this case, make sure the projector is connected to power supply and then press and hold the power button on projector or remote control for 3 seconds to power on the projector. In other cases, please contact customer support or local service center.

IMPORTANT PRECAUTIONS

• Do not look directly at the projection beam with your eyes, because the strong beam may harm your eyes. RG2 IEC 60825-1:2014

• Do not block or cover the heat dissipation holes of the device to avoid affecting the heat dissipation of the internal parts, and damaging the device.
• Keep away from humidity, exposure, high temperature, low pressure, and magnetic environments.
• Do not place the device in areas susceptible to excessive dust and dirt.·Place the device in a flat and stable station, and do not place the device on a surfacethat is prone to vibration.
• Do not allow children to handle the device without supervision.
• Do not place heavy or sharp objects on the device.
• Avoid extreme vibrations, because these may damage the internal components.
• Please use the correct type of battery for the remote control.
• Only use attachments/accessories specified or provided by the manufacturer (such as the exclusive power adapter, bracket, etc.).
• Do not disassemble the device. The device should only be repaired by staff authorized by the manufacturer.
• Place and use the device in a0-40C environment.
• The metal casing is coated with insulating paint.
• The plug is considered as a disconnected device of the adapter.
• The adapter should be installed near the equipment, and should be easily accessible.
• Protect the power cord from being walked on or pinched, particularly at the plugs, convenience receptacles, and the point where this exits from the device.
• Unplug this device if there are lightning storms or when unused for a long period of time.
• Where the power plug or an appliance coupler is used to disconnect the device, the disconnected device would remain readily operable.
• Never touch the power cable or power connector with wet hands.
• Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to local regulations.

STATEMENT

CAUTION!